Function codes
This appendix provides an overview of the available function codes. This gives you quick access to certain functions by pressing the corresponding keys.
Within SwyxWare, certain functions can also be started by entering a function code. The character string is interpreted and executed as a command by SwyxServer. A differentiation is made between
Template Script CodeThese character strings are detected and interpreted by the user's script template.
Note that these codes can only be used within SwyxWare, and not externally.
CTI+ CodeThese DTMF strings are being used in connection with CTI+ (control of telephony devices and control of phones via your phone number). Certain SwyxWare functions can be executed via DTMF function codes, independently of SwyxIt!, directly at the connected devices.
MobileExtensionManager CodeThese DTMF character strings are detected and interpreted by the MobileExtensionManager. They are thus only relevant when connected to the MobileExtensionManager.
Call IntrusionThese function codes are only used in the context of intrusion on external calls (SwyxMonitor option pack required). They are only possible in block dialing, i.e. before the handset is lifted (e.g. with an abbreviated dialing button).
When saving and processing personal data, observe the respective applicable legal data protection regulations. If you have any questions especially regarding data protection in SwyxWare, please contact your administrator.
Feature CodesThese character strings relate to remote inquiries of external voice messages. They are only possible in block dialing, i.e. before the handset is lifted (e.g. with an abbreviated dialing button).
The following function codes are available:
Template Script Code (internal only)
|
##
|
-
|
Initial sequence, which routes a call directly to the user. Additional characters are processed by the user's script (template.vbs).
|
|
##10
|
Remote Inquiry
|
The remote inquiry for the user is activated; the PIN is not queried since the user himself is calling (from his own device)! Sub-menus of the remote inquiry can be reached directly by suffix.
|
|
##20nnn#
|
Call Forwarding Unconditional to nnn
|
 Enable Call Forwarding Unconditional to nnn1.If “*” is entered instead of “nnn”, Call Forwarding Unconditional to Voice Box is activated.Without “nnn”, Call Forwarding Unconditional is deactivated. |
|
##21nnn#
|
Call Forwarding Busy to nnn
|
Enable Call Forwarding Busy to “nnn*”.If “*” is entered instead of “nnn”, Call Forwarding Busy to Voice Box is activated.Without “nnn”, Call Forwarding Busy is deactivated. |
|
##22nnn#
|
Call Forwarding No Reply to nnn
|
Enable Call Forwarding No Reply to “nnn*”.If “*” is entered instead of “nnn”, Call Forwarding No Reply to Voice Box is activated.Without “nnn”, Call Forwarding No Reply is deactivated. |
|
##23
|
Deactivate Call Forwarding Unconditional
|
Deactivate Call Forwarding Unconditional
|
|
##24
|
Deactivate Call Forwarding Busy
|
Deactivate Call Forwarding Busy
|
|
##25
|
Deactivate Call Forwarding No Reply
|
Deactivate Call Forwarding No Reply
|
|
##70*
|
Call All Devices
|
Regardless of the redirection rules, all logged-on terminal devices of the calling user will ring.
|
|
##71*
|
Connect to Voice Box
|
Regardless of all forwarding settings, the calling user will be connected to his own Voice Box. He can then leave himself a voice message.
|
|
##8nnn*ppp#
|
Call Forwarding Unconditional from nnn
|
For the user with the number “nnn”, Call Forwarding Unconditional to the calling line is activated. The given PIN “ppp” is checked.
|
|
##9nnn#
|
Remote Inquiry from nnn
|
The remote inquiry of the user with the number “nnn” is called. The PIN is queried in the Remote Inquiry menu.
|
1 <nnn> stands for extension or external number with public line access or in format **49231123456
<ppp> stands for the PIN
CTI+
|
*0
|
Disable DTMF recognition
|
The DTMF recognition is disabled. This can be necessary in order to send DTMF signals to the call partner. Please use the sequence ## for # here.
|
|
#0
|
Enable DTMF recognition
|
The DTMF recognition is enabled.
|
|
##
|
Send single #
|
Sends a # as a DTMF code to the caller (transparent), when the DTMF recognition is disabled.
|
|
*3
|
Starting a conference
|
A conference is started with active callers and those put on hold.
|
|
*7
|
Hold/Call Swap/Activate
|
The active call is put on hold. A switch is made to a free line or to another line on hold.
If a call has already been put on hold, it can be re-activated by pressing *7.
|
|
*8
|
Exit
|
The currently active call is terminated.
|
|
*9
|
Call Transfer
|
The active call is connected to the call on hold.
|
|
*9nnn#
|
Blind Call Transfer
|
The active call will be connected to “nnn” without inquiry. Requirement: You have only one call.
If the connection with the destination subscriber cannot be established within 20 seconds, the originally received call will be displayed in your SwyxIt! as a call on hold. By pressing *7, the call on hold can be re-activated.
|
In order to use DTMF in connection with SwyxCTI+, the SIP termial devices must support DTMF via SIP-INFO.
The following applies for using DTMF in connection with : SwyxCTI+ If there is an active call on hold and a second call needs to be aborted before being connected, then the DTMF code cannot be used. In this case, hang up on the controlled device. You'll now receive a call back for the line still on hold, and a second call can be initialized again by entering *7.
For SwyxDECT 500 in CTI mode function keys replace the function codes for "Starting a conference", "Hold/Call Swap/Activate" and "Transfer". The "Blind Call Transfer" feature is only available via function codes.
MobileExtensionManager
|
**
|
+ Replacement
|
Replaces the + in a canonical number
|
|
*0
|
Disable DTMF recognition
|
The MobileExtensionManager's DTMF recognition is disabled. This can be necessary in order to send DTMF signals to the call partner. Please use the sequence ## for # here.
|
|
#0
|
Reactivate DTMF recognition
|
The MobileExtensionManager's DTMF recognition is reactivated.
|
|
##
|
Send single #
|
Sends a # as a DTMF tone to the call partner (transparently)
|
|
*1
|
Remote Inquiry
|
Starts personal remote inquiry
|
|
*20nnn#
*20*#
*20#
|
Call Forwarding Unconditional to nnn
|
Enable Call Forwarding Unconditional to “nnn1“.If “*” is entered instead of “nnn”, Call Forwarding Unconditional to Voice Box is activated.Without “nnn”, Call Forwarding Unconditional is deactivated. |
|
*21nnn#
*21*#
*21#
|
Call Forwarding Busy to nnn
|
Enable Call Forwarding Busy to “nnn*”.If “*” is entered instead of “nnn”, Call Forwarding Busy to Voice Box is activated.Without nnn, Call Forwarding Busy is deactivated. |
|
*22nnn#
*22*#
*22#
|
Call Forwarding No Reply to nnn
|
Enable Call Forwarding No Reply to “nnn*”.If “*” is entered instead of “nnn”, Call Forwarding No Reply to Voice Box is activated.Without “nnn”, Call Forwarding No Reply is deactivated. |
|
*3
|
Three-way Conference
|
A three-way conference is opened with the active call partner and the one on hold.
|
|
*4
|
Activate Conversation Recording
|
The recording of conversations is activated. Note that all conversations of the mobile subscriber are recorded.
|
|
*5
|
End Conversation Recording
|
The recording of all conversations is ended.
|
|
*6xxnnn#
|
Initiates the function code xx
|
The function code “xx” (always two characters) is passed on. The transfer of “nnn” is optional. If another parameter is needed, this can be input separated by “*”. The command is ended with “#”. The mobile user can thus act as though he is entering the function code “##xxnnn#” within SwyxWare.
|
|
*600#
|
Start Remote Inquiry
|
Starts personal remote inquiry
|
|
*6002ddd#
|
Access to personal Voice Message
|
Starts playback of the voice message with the ID “ddd”, without date and time
|
|
*7
|
Hold/Call Swap
|
The current call is put on hold. A switch is made to a free line, or to the line previously on hold.
|
|
*8
|
Exit
|
The currently active call is terminated.
|
|
*9
|
Call Transfer
|
The active call is connected to the call on hold.
|
|
*9nnn#
|
Blind Call Transfer
|
The active call will be connected to “nnn” without inquiry. Requirement: You have only one call.
|
|
*9*#
|
Connect to the office device
|
The active call is interrupted, and then put through again to the user's devices (excluding the mobile phone).
|
|
#
|
Call Pick Up
|
Answers an incoming call on a mobile phone, after the call has been accepted bySwyxIt! Mobile. I.e. MobileExtensionManager transmits the call, after it has - mostly by SwyxIt! Mobile - received a “#”.
|
1 <nnn> stands for extension or external number with public line access or in format **49231123456
<ppp> stands for the PIN
Call Intrusion (only possible as block dialing)
|
nnn*24*1#
|
Call Intrusion (listening only)
|
A call that the agent is making with the number “nnn” is intruded in 'listening only' mode.
|
|
nnn*24*2#
|
Call Intrusion (speaking with agent)
|
A call that the agent is making with the number “nnn” is intruded on; the agent can hear the intruder.
|
|
nnn*24*3#
|
Call Intrusion (Conference)
|
The call that the agent is making with the number “nnn” becomes a conference.
|
Feature Code (only possible as block dialing)
|
nnn1 71*
|
Voice Box
|
Calls the Voice Box of user “nnn”, regardless of the selected call forwarding. You can leave a voice message directly.
|
|
nnn*72*
|
Direct Call
|
Calls the user “nnn” as a direct call (Intercom), i.e. a device of the called person is switched at once to output.
|
|
nnn*ppp*8*
|
Call Forwarding Unconditional from nnn
|
For the user with the number “nnn”, Call Forwarding Unconditional to the calling line is activated. The given PIN “ppp” is checked.
|
|
nnn*9*
|
Remote Inquiry from nnn
|
The remote inquiry of the user with the number “nnn” is called. The PIN is queried in the Remote Inquiry menu.
|
1 <nnn> stands for extension or external number with public line access or in format **49231123456
<ppp> stands for the PIN
Last modified date: 10.19.2023